The D956WP has arrived! Based off the D954SW servo, this IP-67 rated version is the true waterproof, dust resistant upgrade for 1/10th-scale Rock Crawlers and Off-Road Trucks. As with our entire “D” line, this technologically-advanced servo is powered by our 32-bit MCU (Microcontroller Unit) and 12-bit ADC (Analog to Digital Converter) industrial science and possess Smart Sense engineering with rapid, high resolution response. The unprecedented programmability and wide-voltage capabilities deliver the most progressive, leading-edge performance for all your radio control needs. With incredibly durable steel gears, dual ball bearing and hardened steel output shaft, the high-end performing D956WP produces the mighty torque and reliability required to take bashers to the next level.
Highlights of the D-Series
Features
- Programmable PWM Digital Amplifier
- 32-Bit MCU with 12-Bit ADC Circuitry
- 4096 Resolution
- 1M Cycle Long Life Potentiometer
- Wide Operating Voltage (4.8 ~ 8.4 Volts DC)
- Dual Ball Bearing Supported Output Shaft
- 25-Tooth Output Spline
- Coreless Metal Brush Motors
- Nylon Reinforced Plastic Upper and Lower Case
- Diamond Cut Aluminum Heat Sink Center Case
- Water Resistant and Waterproof Proof Case
Programmable Functions
- End Point Adjustments
- Direction
- Fail Safe
- Dead Band
- Speed (Slower)
- Soft Start Rate
- Overload Protection
- Data Save / Load
- Program Reset
Accessories
- 3 Steel Alloy Gears Set | Link |
- Metal / Karbonite 1st Gear Set | Link |
- Plastic / Aluminum Case Set | Link |
- Applicable Horns & Screws
D956WP Servo Specifications
| Performance Specifications |
| Operating Voltage Range (Volts DC) |
4.8V ~ 7.4V |
| Speed (Second @ 60°) |
0.19 ~ 0.12 |
| Maximum Torque Range oz. / in. |
251 ~ 405 |
| Maximum Torque Range kg. / cm. |
18.0 ~ 29.0 |
| Current Draw at Idle |
30 mA |
| No Load Operating Current Draw |
500 mA |
| Stall Current Draw |
5,200 mA |
| Dead Band Width |
1 µs |
| Physical Specifications |
| Dimensions (Inches) |
1.57 x 0.78 x 1.46 |
| Dimensions (Metric) |
40.0 x 20.0 x 37.0 |
| Weight (Ounces) |
2.40 |
| Weight (Gram) |
68.0 |
| Circuit Type |
32bit Programable Digital |
| Motor Type |
Coreless Metal Brush |
| Gear Material |
MK 1st Gear & 3 Steel Alloy Gears |
| Bearing Type |
Dual Ball Bearing |
| Output Shaft (type / Ømm) |
H25T |
| Case Material |
Plastic / Aluminum |
| Dust / Water Resistance |
IP67 Rating |
| Connector Gauge (AWG) / Strand Count |
20 / 80 |
| Radio Control Applications |
| Parkflyer |
N / A |
| Sport Plane |
30 – 40% |
| Sailplane |
2 meters and up |
| 3D Performance |
30 – 40% |
| Scale |
30 – 40% |
| Electric Helicopter |
N / A |
| Gas Helicopter |
N / A |
| On Road |
1/8th |
| Monster Truck |
1/8th |
| Buggies |
1/8th |
| Truggies |
1/8th |
| Short Course / Truck |
1/8th |
| Crawlers |
1/8th |
| Sail Boat |
= >1M & Scale |
| Power Boat |
N/A |
